High quality for car size 1.95X4M carbon fiber autoclave in
1. Brief Introduction
In the last ten years we have seen the evolution of new materials,
with excellent mechanical and physical features. The mechanical
resistance, together with the lightness of composite materials, are
finding more and more applications. We call composite material the
product obtained from the polymerization of carbon fibers and
resins, adequately prepared and shaped overlapping coats of fibers
and resin on moulds or cores.
The autoclave is a key equipment for hot-pressing shaping of carbon
fibers and resin matrix composites ( polyimide, bismaleimide, epoxy
resin and thermoplastic resin matrices, etc. ), In fact, the
quality of the product is obtained inside the autoclave reaching an
increase of mechanical features up to 20-30% compared to other
methods of polymerization, which do not foresee the outside
pressurization of the product.
The reliability and the precision of the cycles which can be
obtained with OLYMSPAN autoclave, allow to reach and keep high
quality standards of the product, which is widely used in the
high-tech fields such as aerospace, automotive, electronics,
weapon, traffic, sports equipments and new type of energy, etc.
2. Basic Data
2-1. Model and Size of the Composite Autoclave
Ø Autoclave model: SN-TF19540
Ø Effective diameter: 1950mm
Ø Effective length: 4000mm
Definition: * Effective diameter is the workable diameter of the autoclave.
* Effective length is to point to do the actual length of the composite
2-2. Production Performance
Ø Product size: max. 1800mm x4000mm
2-3. Electric Power
Ø Operating Voltage: 220/380VAC, 3P+N+PE, 50/60Hz
Ø Control Power: 220VAC/50Hz/24VDC
Ø Total power: 136 kw (not including air compressor system and
2-4. Water and Air supply:
Ø Cooling water consumption: ~20m3/h
Ø Cooling water pressure: min.3 bar ~ max. 6 bar
Ø Control air of control equipment: 5 ~ 7bar
Ø Max. Air source for Autoclave: 10 bar
3. General feature and working process of the autoclave
3-1. General feature
OLYMSPAN Autoclave is a sealed pressure vessel which can be heated
by a forced convection heating unit, where temperature, pressure
and vacuum can be controlled effectively. By means of an advanced
design, consisting of a forced convection fun and motor unit,
output heating power system can be adjusted 0-100%,proportional
control of the pressurization, cooling and exhaust components. It
can obtain an uniform temperature and pressure according to the
process curve. Temperature is check in heating, keeping, and
cooling phase. The heating/cooling gradients can be set by
operator. Pressure is adjusted in pressurization, keeping, release
3-2. Working process
The whole working process of OLYMSPAN Autoclave has 17 segments .In
each segment, the value of temperature, pressure, vacuum and
segment time can be set and monitored by HIM and PC, and the
operation process will be realized by our exclusively developed
software which is based on PLC control system to ensure the full
automatic operation.OLYMSPAN Autoclave is suitable for
manufacturing various composite materials, and it also can
guarantee the perfect product quality.
Recipes for example:
Vacu1:minimum vacuum pressure Vac2: maximum vacuum pressure
Press.1: pre-pressure Press.2:final pressure
Temp1:temperature of first segment Temp2: temperature of second
Temp3: temperature of third segment Temp4: temperature of forth
Temp5: temperature of cooling and release
T1: keeping time of first segment T2:keeping time of second segment
T3: keeping time of third segment T4:keeping time of forth segment
(1) Put the blank of composite materials and the moulds into the
vacuum bag, and then put into the autoclave together, finally,
start to vacuum, getting the vacuum to the set point: Vacu1
(2) Start heating, Temperature rise to set point:Temp1, at the same
time, pressurization, the pressure rise to set point: Press.1, and
then starting the first keeping phase , the keeping time is the set
(3) Completed the first keeping phase, continue to heat, the
temperature rise to set point: Temp2, vacuum to Vacu2 or
atmospheric pressure, and then began to start the second keeping
phase, the keeping time is the set point T2.
(4) Completed the second keeping phase,pressurization, the pressure
rise to set point: Press.2.
(5) Continue to heat, temperature rise to set point: Temp3, began
to start the third keeping phase, the keeping time is the set point
(6) Completed the third keeping phase,continue to heat,the
temperature rise to set point: Temp4,began to start the forth
keeping phase, the keeping time is the set point T4.
(7) Completed the forth keeping phase,began to start the cooling
stage,Until the temperature dropped to set point:Temp5.
(8) Air release
3-3. Recipe Preview
You can save and
choose different recipe.
3-4. Control System Structure
3-5. Operation specifications
Ø Pressurization Medium: Compressed Air
Ø Maximum working pressure::1.05Mpa (10.5bar)
Ø Maximum design pressure:1.2Mpa (12bar)
Ø Pressurization rate: 0-0.6bar/min average rate from 0 bar to max.
Ø De-pressurization rate: 0-0.6bar/min average rates from max.
working pressure to 0 bar.
Ø Maximum working temperature:230℃
Ø Maximum design temperature of vessel:250℃
Ø Heating rate: 0-4.5°C/min based on average air temperature from
ambient to 150°C and autoclave with 1200Kgs steel.
Ø Cooling rate: 0-4.5°C/min based on average air temperature from
230°C to 50°C and autoclave with 1200Kgs steel.
Ø Limit vacuum: ≤-0.098Mpa
Ø Maximum working vacuum:-0.08Mpa
4. Equipment Details
4-1. General Structure
4-2. Pressure vessel
Pressure vessel with quick-opening door, certified to 2015 ASME Boiler & Pressure Vessel Code. Manufacturing is according to VIII RULES FOR CONSTRUCTION OF
PRESSURE VESSELS Division 1
4-3. Quick Closing Doors
Ø The whole system consists of four parts: a pair of gear flange,
driven devices, seal ring and high temperature protection system.
Ø Hydraulic operated door opening, closing and locking. It is
controlled by PLC system.
Ø The seal ring is made of silicon rubber, high temperature
Ø It can be manual operated by the switches on the electrical
cabinet near the door also.
Ø Door type: Opening left side. (facing the door)
4-4. Insulation System
Ø Insulation:internal insulation
Ø Insulation material:ceramic fiber
Ø Internal sheet metal: stainless steel, 1.0 mm
Ø Insulation thickness:100 mm
4-5. Floor supports and rails
Ø Rail loadin,Increased log:4500kg,Increased loading can be offered
Ø Rail type::equal angle steel
Ø Floor loading::500kgading can be offered optionally.
Ø Form of floor supports : riffled plate (4mm)
4-6. Heating System
Ø The heating system consists of three heating zones and the
heating elements located in the bottom of the vessel for easy
Ø Electric heating, inconel tubular heaters
Ø Multiple banks controlled via thyristor SCR.
Ø Proportional control, 0-100% output.
Ø The heating process is controlled by temperature controller, the
mode is PID control, and it is organized by PLC system.
4-7. Pressure components
Ø Inlet and exhaust valve, proportionally controlled,
electro-pneumatic adjustable ball valve.
Ø Manual exhaust valve, 3-piece ball valve.
Ø Exhaust silencer (Sounder absorber) makes the noise less than 70DB. 1 pc
Ø Pressure transducer: 1
Accuracy: +/- 50mbar (0.005Mpa)
Ø Pressure gauge:1
Ø Pressure control tolerance:±0.1bar
4-8. Cooling system (heating exchanger)
Ø The heat exchanger is located in the bottom of the autoclave for
Ø Stainless-steel heat exchanger, all internal wetted parts
stainless-steel. Multi-row finned tubing.
Ø Proportionally cooling valve for main cooling control.
Ø Air spray and Mist water valves for pre-cooling control.
4-9. Forced convection system (Air-circulation System)
Ø Hot air channel
OLYMSPAN composite autoclave is different from the conventional
autoclaves. It does not require a radial air-duct and instead
utilizes the floor as the forward air delivery system. This unique
design features decrease the cost for customer, and make the
temperature more uniform.
Ø The Motor fan for circulation
The motor is bolted to the body of the autoclave, it drives the fan
Ø Main parameters of circulating motor fan
Power:22KW,Frequency conversion control
Connecting format:direct-connected ,
Rated rotate speed:960r/min(380V/50HZ),
Fan wheel:7# centrifugal impeller,
Ø Shaft sealing and cooling
Fully sealed special motor, bearings with SKF high-temperature
series. The structure is easy to maintenance. Working use of water
cooling, the shaft water cooling with separate water pump and flow
switch to be fitted to monitor water flow and automatically
alarm/stop the cycle if there is not enough water flow.
4-10. Temperature monitoring components
Ø Temperature control tolerance:±2.5°C
Ø Air temperature thermocouples: 1 ,fixed
Type-K, including PC monitoring/ control,data-acquisition
Ø Hi-Limit safety thermocouple: 1 fixed
Type-K, including PC monitoring/ control
Ø Part thermocouple:12, can be movable
Type-K, including PC monitoring, data-acquisition, and control.
4-11. Vacuum system
4-11-1 Vacuum source ports: 6 total
4-11-2 Each source port will include:
Ø ½" internal thread pipe joint
Ø PC-controlled vacuum select valve, 3-piece ball valve,
Ø PC-controlled vent-vent select valve, 3-piece ball valve,
Ø Stainless-steel tubing, ¼"
4-11-3 Vacuum transducer ports: 6 total
4-11-4 Each Vacuum transducer port will include:
Ø ½" internal thread pipe joint
Ø 3-piece ball valve, stainless-steel
Ø Stainless-steel tubing, ½"
4-11-5 Vacuum Transducer: 6 total
Ø Proof pressure: 10Bar
Ø Range:-760mm Hg to 10 bar
Ø Accuracy: +/- 15.6mm Hg
4-11-6 Vacuum filter: 6 total
For composite curing applications with high volatile content (ie.
high-temperature polyimides), the vacuum filter will be much more
effective condensing volatiles and solvents during high-temperature
4-11-7 Each vacuum source individually controlled, it can be done vacuum
and vent. And each will be individual shut off in case of vacuum
4-11-8 Separation of vacuuming and measuring.
4-11-9 Automatic vacuum leakage test before start a circle.
4-12. Control System
Ø The Control System is developed based on the research and
development toward composite material field, and it is made up of
one PLC for the automatic managing of the process and one PC for
the supervision of the system. The operation of the whole system is
based on the exclusive developed software package-TPC(Thermal
Ø Password protected entry access, operator can log into the system
by accessing the security login form with a name and password.
Ø Full automatic operation including heating, pressuring, vacuum,
vent, cooling and exhaust actions. Monitoring and display run
status information, data saving information, integrity check
information and run override controls, such as change segment, end
Ø Manual operation screen allows operator take manual control
temperature, pressure, vacuum, fan, and valves as allowed.
Ø According to the different working process requirement, it can
set segment time, control TC, temperature value, temperature rate,
vacuum value, pressure value, pressure rate, etc. before curing,
and it also can modify the parameter on live operation.
Ø It can choose and save the different curing recipe, display a
real time and historical trend of the pressure, vacuum and
temperature; storage all processing data and its paperless record
function can realize reporting of working curve and process
Ø It can monitor all actions of devices and the safety system
information continuously, such as safety interlock, door closed,
door locked and so on.
Ø It has audible and visual alarm system and diagnostic and fault
finding screen, including over-temperature and over-pressure alarm
and various safety protection functions, such as vacuum leakage,
over cure cycle deviations, component failure, etc.
Ø Heating control will allow operator to control from product or
air or minimal T/C reading, the TPC has control TC, operator can
choose air TC, High TC, or low TC.
Ø TPC has calibration and certification screen for all of sensors.
Calibration is normally required whenever a sensor value is
inaccurate when compared to a certified standard.
Ø Customer can operate register, login and typing in product
information, and realize intranet or remote control.
Ø It can realize data output, printing, analyzing requirements to
improve product quality.
Ø UPS (uninterruptible power supply), power:1000VA
4-13. Safety systems:
Ø Mechanical and electrical interlocks for door closure, door
closed and locked proof of position, the autoclave can not be
opened when pressure in the autoclave higher than 0.2 bar.
Ø It will be auto-alarm when facing over-temperature or
over-pressure; auto drop the temperature when over temperature, and
auto-release when over pressure.
Ø It has emergency valve for pressure release.
Ø Pressure safety relief valve, certified to ASME
Ø Low supply air pressure alarm, low pressure switch and low
Ø Circulation fan motor tripped indication.
Ø Man in autoclave-safety device to cut off the total autoclave
Ø Audio visual alarm when door opening closing is in operation.
Ø Emergency stop push button to abort the cure cycle all pressure
control valves, depressurization control valves, main cooling will
fail to safe.
OLYMSPAN autoclave will be primed and painted high-gloss "Dark
Blue" color. Customer
requested color can be quoted optionally.
5. Main technical data of composite autoclave
|MODEL#SN-CGF19540 COMPOSITE AUTOCLAVE—TECHNICAL PARAMETER|
|No.||Description||Unit||Specifications and Parameters|
|1||Effective Working Diameter||mm||1950|
|2||Effective Working Length||mm||4000|
|3||Autoclave Track Distance||mm||1150|
|4||Track height( from floor to Track plane)||mm||850|
|6||Max. Working Pressure||Mpa||1.05|
|7||Max. Pressurization Rate (average)||bar/min||0.6|
|8||Max. Depressurization Rate (average)||bar/min||0.6|
|9||Safety valve exhaust||Mpa||1.15|
|11||Max. Working Temperature||℃||230|
|12||Max. Heating Rate(Air average)||℃/min||4.5|
|13||Max. Cooling Rate (Air average)||℃/min||4.5|
|14||Thermal load during test||Kg||1200kg steel|
|15||Temperature uniformity at steady state||℃||±2|
|16||External shell temperature at max. temperature||℃||<60|
|17||Quick opening Door Mode||---- ||hydraulic|
|18||Working Medium||---- ||Compressed Air|
|19||Heating Mode||---- ||Electric(Convection+Radiation )|
|20||Heater||---- ||inconel tubular heaters|
|22||Quantity of Circulating Fan Motor||Set||1|
|23||Power of Circulating Fan Motor||KW||22|
|24||Thermocouple type||---- ||Type K|
|25||Air Temperature Thermocouples||Piece||1|
|26||Part Temperature Thermocouples||Piece||12|
|27||Quantity of Pressure Transducer||Piece||1|
|29||Quantity of Vacuum Probe||Piece||6|
|30||PLC-controlled valves on each vacuum line||--- ||Vacuum and Vent|
|31||Min. Vacuum Pressure||Mpa||-0.08|
|33||Standard Control Mode||--- ||PLC+PC|
|34||Control Software||--- ||Thermal Processing Control (TPC)|
|35||Insulation Type||--- ||Internal|
|36||Insulation Material||---||Ceramic fiber|
|38||Insulation Sheet metal||--- ||Stainless Steel|
|39||Working environment temperature||℃||Min.—20℃,max +45℃|
|40||Working environment humidity||--- ||<60%|
|41||Power supply||--- ||220/380VAC, 3P+N+PE, 50/60Hz|
6. The TPC control system (Thermal process control)
6-1 Brief introduction of TPC
The autoclaves components and sensors will be monitored and
controlled by the TPC control system. TPC is the Windows XP version
of OLYMSPAN’s computerized control software. TPC was developed by
OLYMSPAN in 2006 to be a single software control platform for most
6-2 Superior Control is Your Key to Performance
Most will agree that in the world of composites manufacturing, the
control system is a key component to assuring autoclave
performance, usability, and reliability. Even the best autoclave
will be crippled by a poor performing control system, especially
when processing large volumes of composites. Because of this fact,
OLYMSPAN has focused a large portion of our R&D efforts on our
control software and the features/capabilities that can improve
processing performance, reliability, and lean manufacturing in
6-3 TPC Software – Features and Capabilities
The autoclave will be controlled by proven TPC computerized control
software, configured in either a single PC or in a primary and
backup architecture (optional).
Ø Ease of use - Even though TPC is by far the most advanced control software
product on the market, the software is still very easy to use. All
screens and features are designed to maximize usability and
increase operator efficiency. For example, part entry, leak-tests,
and other pre-run operations have been stream-lined to reduce the
"door open" times of equipment.
Ø Security- TPC Software include the ability as follow:
l To create user accounts for each operator, supervisor, or
l To assign specific and independent permissions and restrictions
to each user.
l To track user login and logout operations, including time
l To program an auto-logout after a specific period of operator
Ø Excellent reliability – TPC is designed as a client-server package with proven
reliability in the field. It is unacceptable to OLYMSPAN and to our
customers to have control applications that "lock up", and that is
why TPC is designed and tested to meet stringent up-time
specifications. Many of our TPC single-PC systems are controlling
multiple pieces of equipment for years without any major trouble
incident. The production-time of TPC is far better than all
Ø Auto-Redundancy (optional) – TPC supports 100% redundancy of operations and data by means of
a second PC. In a TPC Level II and III systems, two PCs are used
for primary and backup control of the equipment. In the highly
unlikely event of primary PC failure, the backup PC will take
control and continue the run(s) seamlessly. The backup PC will also
have a complete backup copy of the data up until and after the
primary PC failure. During normal operation, both PCs can be
utilized for viewing and/or operation.
Ø Advanced Cure Control - OLYMSPAN is the leader in design and implementation of advanced
controls for the curing of composites in autoclaves of China. The
TPC software contains hundreds of options designed specifically to
enhance the product quality. These include advanced recipe control,
control by air temperature, control by part temperature, controlled
by part gradient, controlled by air gradient, exothermic control,
and other material properties, pro-active control, and many others.
Ø Comprehensive Reporting - TPC has an extensive reporting capability that if far more
powerful and flexible than those provided with other packages. You
can select specific runs by database query and view and/or print
trend date in color plot format, numeric logs, pass/fail reports,
message logs, and a host of other formats. On-screen zooming and
panning on the trend view is also supported.
Ø Remote Control/Viewing - TPC is the only package capable of being viewed and control by
multiple PCs on a single customer network. Unlike other competing
products which utilize PC-Anywhere to "take control" of the
equipment PC, TPC allows concurrent operation and viewing of the
process by operators, engineers, QA/QC personnel, and managers on
the network. As many as 10 concurrent clients are supported.
Ø Up to Date - TPC is maintained and updated regularly to provide the most up
to date features and capabilities as requested by our users.
6-4 Sample Screen Images
The following screen images are provided for a typical OLYMSPAN
composite autoclave implementation.
All screens are customized to each customer’s requirements.
Graphic and animated process and instrumentation screens are
standard with all autoclaves
Full automatic operation control and monitor run status
information, data saving information, integrity check information
and run override controls
5-step pre-run integrity checks, including field check, sensor
check, vacuum check, drawdown check and leak check
Manual operation screen allows operator take manual control
temperature, pressure, vacuum, fan, and valves as allowed.
Monitoring and display all selected thermocouples, vacuum probes
and the reading of theirs
Recipe editing is via spreadsheet and includes audit-tracking,
revision control, and complete sequencing of all aspects of a cure
Real-time and post-analysis trending includes panning, zooming, and
8,Configurations of composite autoclave
Ø PC: Dell
Ø PLC: Siemens
Ø Main electrical component : Schneider
Ø Shell:ASME certificate standard OLYMSPAN,CHINA
Ø Heater : Electric heating inconel tubular heaters.
Ø Insulation material: Ceramic fiber
Ø Protect armor: Stainless steel
Ø Heating exchanger:304 stainless-steel, XUELANG, China
Ø SCR: SHIMADEN, China
Ø Electro-pneumatic adjustable ball valve: YAMATAKE, Japan
Ø PID controller : Omron ,Japan
Ø Limited Switch: Omron ,Japan
Ø Special Motor: OLYMSPAN, China
Ø Thermocouple: OMEGA
Ø Pressure transducer: Honeywell
Ø Vacuum pump: BUSCH.
9-1. The equipment will be properly packed / wrapped considering
long-distance ocean and land transportation and rough handling that
may happen in the absence of both parties.
9-2. Proper protection from moisture, rust, mold, scratches, shaking,
etc, will be taken so that the goods may arrive at the installation
site in good condition.
9-3. Shipping marks and warning signed will be clearly painted, and
detailed packing list (in
English) will be soundly attached, to the outside of the packing.
10. Delivery, Installation and Quality Guarantee
The delivery period is 150 days after receiving down-payment; but
does not include shipping time!
10-2-1 The installation and commissioning takes 1 person x 20 days (max.)
under Buyer’s assistance. Production training is carried out during
the same period.
10-2-2 The international travelling cost, including round-trip air
tickets, insurance, boarding and meals of the Seller’s service team
should be charged to the buyer.
10-3. Quality Guarantee
The Seller provides 14 months quality guarantee, during which the
Seller is responsible for all equipment failures due to inferior
quality, improper design or services.
11. Workshop View
12 .PAYMENT TERM
The contract value shall be paid by the buyer to the seller in the
1. 30% of total value will be paid by T/T as down payment.
2. 20% on submission of approval drawings by T/T
3. 40% due upon shipment
5. 10% after customer acceptance, or 60 days after delivery maximum
Alternate terms may be considered, though modification of terms may
affect overall price of system.
13. Service terms
13.1 Service before sale:
Provide relative technical data for customer choosing equipments.
Design floor plan, basic general drawing and quotation.
13.2 Service in sale:
After the contract working, we will execute each item and keep
relevant standards strickly in every manufacturing process. Keep in
touch with customer and make sure that craft, quality and
technology could meet the requirements.
13.3 Service after sale:
Help customer for installation and training at site. Maintenance
and repair for one year. Customer should pay for the round-trip
flight ticket and accommodation.
14. Quotation Validity
Our quotation will be available in 30 days after we send it you by a formal way: fax, email or courier.
15. More terms and conditions will be explained in the final
The entire OLYMSPAN Team thanks you for the opportunity to submit
this quotation. Each team member appreciates the opportunity to
work with you and looks forward to the opportunity to exceed your
expectations. Should have any questions, requirements or ideas,
please don’t hesitate to contact the undersigned.